A Capsule Spec Sheet, Line by Line: Fill Weight, Disintegration, Moisture and Shell
By the Silk Foods Ceylon Editorial Team
Buyer’s snapshot
- A capsule spec sheet is four numbers and a signature: a fill-weight tolerance, a disintegration time, a moisture limit and a shell choice. Each one has a cost if it slips.
- Two pharmacopoeias set the usual fill-weight yardsticks. For a 400 mg average fill, the European method allows 7.5% (370 to 430 mg), and the US dietary supplement method allows 90% to 110% of the average (360 to 440 mg) (Ph. Eur. 2.9.5; USP <2091>).
- Gelatin shells normally hold 13 to 16% water. Standard HPMC shells hold about 3 to 8%, depending on the maker (supplier literature, 2026).
- Silk Foods Ceylon (SFC) fills herbal hard-shell capsules into 60-count bottles. Small runs are welcome and quoted on request.
A brand owner sends a draft capsule spec sheet back with one line circled: “weight variation: within limits.” Within which limits? Measured how? Against what average? The line reads like a promise and works like a shrug.
This post walks a capsule spec sheet from top to bottom. It follows the order a QA reviewer reads it, and for each line it asks the same three questions: what number goes here, what does it cost if it slips, and who signs for it at batch release. The worked numbers are illustrative planning figures, not SFC data or a quotation. The pharmacopoeia limits are real and are cited in the Sources block.
If you are still deciding the capsule size and bottle count, start with the post on fill weight, cap size and bottle count. This one starts after that decision is made.
What belongs on a capsule spec sheet?
Seven lines carry most of the weight. The first four are the subject of this post.
| Line | What it controls | What the sheet should state |
|---|---|---|
| Fill weight and tolerance | Dose per capsule and label claim | Target in mg, the method, the limit, the sample size |
| Disintegration | Whether the capsule opens when it should | Medium, time limit, the method it follows |
| Moisture | Shelf life, shell integrity, caking | Limit on the powder and on the filled capsule, test method |
| Shell | Gelatin or HPMC, size, colour | Material, size, colour, any vegetarian claim |
| Identity and microbial limits | Right herb, safe powder | Reference to the raw-material file |
| Pack | Bottle, desiccant, seal, label | 60-count bottle, white or black, closure |
| Release | Who signed it | Role of the signer, record reference |
A sheet that states only “complies” on a line has told the reader nothing. A good sheet names the number, the method and the record.
How should fill weight and its tolerance be written?
Write the target as an average content mass in milligrams, then say which method judges it. Two are common, and they do not agree.
The European method (Ph. Eur. 2.9.5) weighs 20 capsules and compares each to the average. For an average under 300 mg the allowed deviation is 10%; at 300 mg or more it is 7.5%. No more than two capsules may fall outside that band, and none may fall outside twice the band. For capsules the content is found by weighing the shell and subtracting it.
The US dietary supplement chapter (USP <2091>) is blunter for hard capsules: weigh 20 intact capsules, and each must sit between 90% and 110% of the average weight.
Here is what that means for an illustrative 400 mg average fill.
| Rule | Band for each capsule | Outliers allowed |
|---|---|---|
| Ph. Eur. 2.9.5, 7.5% | 370 to 430 mg | Up to 2 of 20, none beyond 340 to 460 mg |
| USP <2091>, 90% to 110% | 360 to 440 mg | None |
The sheet should say which of the two the batch is judged against, and it should say it once, not leave each reviewer to assume. Pick the one your retailer’s QA team already uses. If your product will also be sold outside Sri Lanka, say so in the brief now, because the destination may name its own method.
What it costs if it slips. Over-fill is cheap to see and easy to ignore. Take 60 capsules in a bottle. A mean over-fill of 5% on a 400 mg target is 20 mg per capsule, or 1.2 g of extra powder per bottle. At an assumed LKR 6 per gram of blended powder (a planning figure only), that is LKR 7.20 per bottle given away in every bottle sold. Under-fill is worse: the capsule no longer delivers what the label says, and the label claim is the thing a buyer’s QA team will test first.
Who signs. The batch record should carry the 20-capsule result, and the QA lead reviews it. The signer is a role on the record, not a name on the sheet.
How should disintegration be specified?
State the time limit, the medium and the chapter it follows. The US dietary supplement chapter (USP <2040>) sets a 30-minute check in the basket apparatus for capsules; read the current text for the medium it names for hard shells, because reviews of the chapter note that it differs from the general drug chapter.
Soft-shell products follow a different rupture test in that chapter. SFC does not offer softgel or oil encapsulation, so that route is outside this sheet, and a brief that needs it should go to a different supplier.
What it costs if it slips. A powder that is too fine, too hydrophobic or over-lubricated can cling together inside the shell and open slowly. The capsule still looks perfect on the bottle shelf. The failure shows up in a retailer’s own test, or in a customer complaint. Putting the limit on the sheet means the question is answered before the first bottle ships rather than after.
Who signs. The release record shows the test result against the stated limit. If the sheet says 30 minutes, the record says 30 minutes. Do not accept “passes” alone.
What moisture limit goes on the sheet?
Two limits, not one: the powder going in and the finished capsule coming out. They connect through the shell.
Gelatin shells are made to hold about 13 to 16% water; below that they turn brittle and crack on handling. Standard HPMC shells carry far less, about 3 to 8% depending on the maker, and low-moisture grades go lower still (supplier and review literature, 2026). A dried herb powder is hygroscopic. Put a drier powder in a gelatin shell and it can take water from the shell. Put a wetter one in and it can soften the shell and cake inside.
So the sheet needs a loss-on-drying limit for the fill, and the limit should be set from the powder’s own data and the supplier’s file, not copied from another herb. The number below is a placeholder to show the format.
| Test | Illustrative limit | Basis |
|---|---|---|
| Fill powder, loss on drying | 8% or less (placeholder) | Set from the raw-material file for each herb |
| Shell, water content | Per shell supplier certificate | Gelatin about 13 to 16%; HPMC about 3 to 8% |
| Filled capsule | Stated in the release record | Checked before sealing the bottle |
What it costs if it slips. Moisture is the quiet cause of short shelf life. It shows up as clumped powder, a tacky capsule or a cracked shell months after the batch left the plant. The bottle choice and desiccant matter too, and the post on white versus black capsule bottles covers that side. Hygroscopic blends are the hardest case, and the post on nutricosmetic capsule blends takes it further.
Gelatin or HPMC: which shell goes on the sheet?
The choice is a spec line, not a cosmetic one. It changes the moisture behaviour above and the claim on the front of the label.
| Question | Gelatin | HPMC |
|---|---|---|
| Typical shell water | About 13 to 16% | About 3 to 8% |
| Suits a moisture-sensitive fill | Less well | Better |
| Vegetarian or vegan claim | Not available | Available, if the rest of the pack supports it |
| Brittleness risk when dry | Higher | Lower |
If the brand will say “vegetarian” or “vegan” on the pack, the shell must support it and the sheet must say so. If the herbs are strongly hygroscopic, HPMC is worth a conversation. If neither applies, gelatin is a reasonable default. Either way, put the material, size and colour on the sheet so nothing is decided by whichever shell was in stock.
Product category matters here too. A capsule with Ayurvedic or health claims has registration steps of its own, set out in the posts on the food supplement, Ayurveda and pharmaceutical routes and on Ayurvedic capsules and SLSI. The spec sheet supports that file. It does not replace it.
What do first capsule briefs usually get wrong?
The common instinct is to keep the sheet short, because fewer lines mean fewer arguments. It is the wrong way round. The arguments that cost time rarely come from a long sheet. They start after the batch exists, when nobody wrote down which pharmacopoeia judged the fill weight. A longer sheet settled in week one is cheaper than a short one disputed in week six.
Where is a spec sheet the wrong first step?
Be honest about fit. A tight capsule sheet is a poor use of anyone’s time when the formula is not final, the herb source is still being chosen, or there is no plan for the registration the product needs. If the recipe is still moving, spend the first weeks on formulation and the raw-material file. The sheet should follow a signed formula, not lead it.
How does batch release actually get signed?
Release is the last line, and it is where the other lines meet. A workable pattern has four parts:
- The fill-weight result for the 20-capsule sample, against the named method.
- The disintegration result against the stated time limit.
- The moisture results for the powder and the finished capsule.
- A signature by role (the QA lead) with the batch record reference.
If any line is blank, the batch is not released. The sheet should say so in plain words.
Frequently asked questions
What is a fill weight tolerance on a capsule spec sheet?
It is the allowed spread of content mass around the average, usually checked on 20 capsules. Under the European method the band is 10% below a 300 mg average and 7.5% at 300 mg or more (Ph. Eur. 2.9.5). The US dietary supplement chapter uses 90% to 110% of the average for hard capsules (USP <2091>). The sheet should name the one it follows.
How long should a herbal capsule take to disintegrate?
The US dietary supplement chapter sets a 30-minute basket test for capsules (USP <2040>). Read the current chapter for the medium used for hard shells. The spec sheet should state the time, the medium and the chapter, and the release record should show the measured result against it.
Is HPMC better than gelatin for herbal capsules?
Neither is better in every case. Gelatin shells hold about 13 to 16% water, and standard HPMC shells about 3 to 8%, so HPMC suits moisture-sensitive fills and supports a vegetarian claim (supplier literature, 2026). Gelatin is a reasonable default when neither matters. State the choice on the sheet.
Does Silk Foods Ceylon offer contract manufacturing for herbal capsules?
Yes. Silk Foods Ceylon (SFC) fills herbal hard-shell capsules into 60-count bottles, white or black, as part of Contract Manufacturing and Private Labelling. Small runs are welcome and quoted on request. SFC does not offer softgel or oil encapsulation. A brief to b2b@esilkroute.com.lk starts the conversation.
How Silk Foods Ceylon can help
For local FMCG brands moving a capsule range from a draft sheet to a signed one, Silk Foods Ceylon (SFC) runs Contract Manufacturing and Private Labelling for herbal capsules in 60-count bottles at its Matale facility. Small first runs are welcome and quoted on request. The in-house R&D team agrees a formulation within 3 to 4 weeks of a signed brief at most, and the spec sheet is settled alongside it. The facility is BRCGS- and FSSC 22000 V6-audited, with SLSI submission support inside a standard engagement.
To brief a project, email b2b@esilkroute.com.lk or call +94 77 157 7294.
Sources
- United States Pharmacopeia, general chapter <2091> Weight Variation of Dietary Supplements. Retrieved 2026-11-17. https://www.drugfuture.com/Pharmacopoeia/usp38/data/v38332/usp38nf33s2_c2091.html
- United States Pharmacopeia, general chapter <2040> Disintegration and Dissolution of Dietary Supplements. Retrieved 2026-11-17. https://drugfuture.com/Pharmacopoeia/usp38/data/v38332/usp38nf33s2_c2040.html
- European Pharmacopoeia, 2.9.5 Uniformity of Mass of Single-Dose Preparations (reproduction of the EP 7 text). Retrieved 2026-11-17. https://www.drugfuture.com/Pharmacopoeia/EP7/DATA/20905E.PDF
- Tablets & Capsules, “Using Next-Generation HPMC Polymers as an Alternative to Gelatin for Hard Capsules” (shell moisture ranges). Retrieved 2026-11-17. https://www.tabletscapsules.com/3641-Technical-Articles/588363-Capsules-Using-Next-Generation-HPMC-Polymers-as-an-Alternative-to-Gelatin-for-Hard-Capsules/
Worked figures (400 mg fill, LKR 6 per gram, 8% loss on drying) are illustrative planning assumptions, not SFC data or a quotation. Pharmacopoeia text is summarised from the sources above; check the current official edition before putting a limit in a contract.


